Outdoor Dome Series Hardware Manual E89 2014/01/21
www.acti.com Hardware Manual 10 4) Audio Input / Output This connector connects to audio input and output devices, such as micropho
www.acti.com Hardware Manual 11 Connecting Audio In / Out Devices (Optional) on page 34 for more information. 5) Reset Button The
www.acti.com Hardware Manual 12 Mounting Options There are several mounting options that you can use to install the camera. Select t
www.acti.com Hardware Manual 13 Mount Types Accessories Straight Wall Mount Suitable when mounting the camera on straight walls. P
www.acti.com Hardware Manual 14 Other Mounting Accessories Accessories PMAX-0104 (Extension Tube) PMAX-0700 (Junction Box) NOTE:
www.acti.com Hardware Manual 15 Installing the Camera on a Surface This section describes the procedures in installing the camera on
www.acti.com Hardware Manual 16 Step 2: Open the Dome Cover NOTE: To avoid scratches or leaving fingerprints on the dome cover, it i
www.acti.com Hardware Manual 17 4. If necessary, insert a memory card, with the metallic contacts facing down, into the card slot o
www.acti.com Hardware Manual 18 Step 3: Prepare for Waterproof Installation The camera comes with two (2) glands used for waterproof
www.acti.com Hardware Manual 19 Waterproof Solution with Naked Cable This section describes the procedures in using the bundled cabl
www.acti.com Hardware Manual 2 Table of Contents Precautions ... 4 Safety
www.acti.com Hardware Manual 20 4. Attach the cable gland body to the hole of the camera. Attach to Camera Side Hole
www.acti.com Hardware Manual 21 Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling con
www.acti.com Hardware Manual 22 2. Disassemble the bundled conduit gland as shown below: NOTE: In this installation, the condui
www.acti.com Hardware Manual 23 5. Insert the sealing insert and attach it at the end of the flex conduit. 6. Screw the co
www.acti.com Hardware Manual 24 b. Insert the sealing nut into the conduit gland body and then attach the clamping nut as tigh
www.acti.com Hardware Manual 25 Step 4: Install the Camera to the Surface 1. Align the camera screw holes and the cable hole (if ne
www.acti.com Hardware Manual 26 Step 5: Connect the Cable 1. If the cable will be routed along the surface, pull the network cable
www.acti.com Hardware Manual 27 3. Connect the other end of the network cable to a switch or injector. Then, connect the switch or
www.acti.com Hardware Manual 28 Step 7: Adjust the Viewing Angle Based on the live view, adjust the viewing angle and orientation of
www.acti.com Hardware Manual 29 The camera comes with the focus and viewing angle already pre-fixed. However, if you need to change
www.acti.com Hardware Manual 3 Other Adjustments and Accessories ... 35 Replacing the Dome Cover ...
www.acti.com Hardware Manual 30 Step 8: Close the Dome Cover 1. Tighten the three (3) screws to attach the dome cover to the camera
www.acti.com Hardware Manual 31 Other Connections This section describes the procedures in preparing the external devices that you c
www.acti.com Hardware Manual 32 To connect input devices (DI), map the pins to one of the pin combinations below: Device Pin Mappi
www.acti.com Hardware Manual 33 In this case, wire connection to Pins 1 to 4. Use the GND and DI1 pins to connect a DI device and us
www.acti.com Hardware Manual 34 The illustration below is a graphic example of connecting a relay to a high voltage DO device. Rela
www.acti.com Hardware Manual 35 Connecting Audio In / Out Devices (Optional) Depending on your surveillance needs, you may connect a
www.acti.com Hardware Manual 36 Other Adjustments and Accessories Replacing the Dome Cover For more discrete surveillance needs, the
www.acti.com Hardware Manual 37 4. Remove dome cover from the cover housing. 5. Remove the rubber from the dome cover. 6. Inser
www.acti.com Hardware Manual 38 8. There are 3 indents on the cover housing; note the indent (a) which is on the center of the exte
www.acti.com Hardware Manual 39 10. Fit the screw into the spring wire that is attached to the camera. Note the screw placement as s
www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before
www.acti.com Hardware Manual 40 Using a Memory Card The camera supports local video recording or saving of snapshots to a memory car
www.acti.com Hardware Manual 41 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera f
www.acti.com Hardware Manual 42 Double-click on the camera model name, the default browser of the PC is automatically launched and t
www.acti.com Hardware Manual 43 Use the default IP address of a camera: If there is no DHCP server in the given network, the user ma
www.acti.com Hardware Manual 44 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in
www.acti.com Hardware Manual 45 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are u
www.acti.com Hardware Manual 46 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser
Copyright © 2014, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu D
www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with t
www.acti.com Hardware Manual 6 Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. At
www.acti.com Hardware Manual 7 Introduction The List of Models This hardware manual contains the following models: E89 10MP Outdoor
www.acti.com Hardware Manual 8 Package Contents Camera Mounting Screw Kit Hexagon Screwdriver Drill Template Conduit Gland Cable
www.acti.com Hardware Manual 9 Physical Description NOTE: The camera images in this documentation are for reference only. Actual cam
Commenti su questo manuale